RMS 200W High Power Stator/CDI/Voltage Regulator AC To DC Charging System Upgrade (Yamaha)

Brand-new kit stator 200W + voltage regulator rectifier + flywheel + puller + external ignition coil + PeakRPM CDI box.

• Direct replacement to your original unit.
• Plug-and-play, direct fit, easy installation.
• Connector included.
• All shipped products are tested.

All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part.

High output stator 200W

• Highest grade of lamination materials.
• Highest grade of copper winding, resistant to 200 degrees Celsius.
• Pick up pulsar coil included.
• Rubber grommet included.
• Back plate included.

Voltage regulator rectifier

• The quality exceeds the OEM equipment.
• Improved heat sink and charging capabilities.
• Higher grade of electric components.

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Please note that the connector is not the same as the original. You must install the opposite connectors included in the box for the kit to work on Banshees.

Improved stronger magneto flywheel rotor

RMSTATOR is offering a replacement flywheel with stronger magnets for your Yamaha, this flywheel can be used as a direct replacement to the OEM.

We suggest combining it to our 100 or 200 watt stator as it will run the lights better in the lower rpm.

Flywheel puller

• 27 mm × 1.0 left hand male.
• Includes crankshaft thread protector cap.

PLEASE CHECK IF YOUR MAKE/MODEL IS COMPATIBLE BEFORE BUYING.

External ignition coil

• Highest grade of lamination materials.
• Spark plug cap(s) included.

PeakRPM CDI box

• Our PeakRPM CDI Box provides the optimal output for your ride.
• Higher grade of electronic components.
• The quality exceeds the OEM equipment.

Specifications:

High Output Stator 200W

Dimensions:
Interior diameter: 103 mm
Exterior diameter: 34 mm
Thickness: 27 mm
Length of wire stator to grommet: 60 mm
Length of wire grommet to plug: 520 mm
Length of pickup coil's wire to grommet: 80 mm

Other specifications:
Number of wires: 6
Number of plugs: 3
Number of pins: 6

Wire to wire resistance:
Alternator: Yellow to Black = 0.4 ohms +/-20%
Pickup: White/Green to White/Red = 115 ohms +/-20%
Source: Green to Red = 12 ohms +/-20%

Voltage Regulator Rectifier

Dimensions:
Width: 55 mm
Length: 67 mm
Height: 22 mm
Fixation holes centre to centre: 55 mm
Wire length: 140 mm

Other specifications:
Number of plugs: 1
Number of pins: 4
Minimum charging voltage: 14.5V +/- 0.5V
Maximum charging current: 25A-35A/300W-500W
Open circuit voltage: <15V
Operation temperature: -20? to 85?

Flywheel rotor

Dimensions:
Exterior diameter: 128 mm
Interior diameter: 105 mm
Interior diameter centre housing: 21 mm
Exterior diameter centre housing: 34 mm
Thickness (exterior): 12 mm
Thickness (interior): 7 mm

External ignition coil

Bracket centre to bracket: 90 mm
Wire length: 590 mm
Primary resistance: 0.4 ohms
Secondary resistance: 6.0K ohms
Spark plug cap resistance: 5K
Voltage transfer ratio: 150:1
Insulation resistance: >1000M

High performance CDI box

Dimensions:
Height: 26 mm
Length: 87
Width: 72 mm
Fixation holes centre to centre: 85 mm

Other specifications:
Number of plugs: 2
Number of pins: 8