Snowmobile Studs & Nuts
- WOODY'S Remove filter
- Clear all
WOODY'S ROUND DIGGER SUPPORT PLATE
WOODY'SQuick & easy to install – no indexing required High-grade, lightweight aluminum support plates for two-ply studs Must be paired with correspon...
View full detailsWOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S STUD SHARPENING TOOL
WOODY'SSteel stud sharpener (not intended for carbide use) Available in 30°, 45°, and 60° Replacement inserts available
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S CARBIDE RUNNER
WOODY'SWear Bar available Ace Dooly Executive Extender Trail III Hardweld Maverick Slim Jim 2.0 Standard Trail Blazer IV
WOODY'S 8" X 60 TURNING 1 1/2" END PAD (WYV-6580-1)
WOODY'SWoody’s most popular carbide4” turning carbide that has a sharp 60° edge angle for performance cornering; 1-1/2” carbide wear pads help extend runn...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (TYV4-6500-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (TAT4-9750-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S 8" X 60 TURNING 1 1/2" END PAD (WCA-5000-1)
WOODY'SWoody’s most popular carbide4” turning carbide that has a sharp 60° edge angle for performance cornering; 1-1/2” carbide wear pads help extend runn...
View full detailsWOODY'S ROUND SOCKET FOR COLORED WASHERS
WOODY'SAvailable in 5/16" sizeA unique tool used for driving locknuts down on push-through studsProvides the torque to tighten without touching the surfac...
View full detailsWOODY'S 6"X 60 TURNING 1 1/2" END PAD (TSD4-9350-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S STUD SHARPENING TOOL 60 DEGREES
WOODY'SEasy to useJust put the tool into a 3/8" drill chuck and sharpen studs while on the sled
WOODY'S SNO-CROSS CARBIDE RUNNER 10" C&A PRO SKI
WOODY'SCompetition-legal snocross wear bars; combined height of bar and carbide conforms to ISR rulesFeature 60° turning carbide and 5/8" bar thicknessSom...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (TYV4-6580-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (TAT4-9975-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S 8" X 60 TURNING 1 1/2" END PAD (WAT-9975-1)
WOODY'SWoody’s most popular carbide4” turning carbide that has a sharp 60° edge angle for performance cornering; 1-1/2” carbide wear pads help extend runn...
View full detailsWOODY'S 6"X 60 TURNING 1 1/2" END PAD (TSD4-8250-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S STUD SHARPENING TOOL 30 DEGREES
WOODY'SEasy to useJust put the tool into a 3/8" drill chuck and sharpen studs while on the sled
WOODY'S 6" X 60 TURNING 1 1/2" END PAD (TCA-5000-1)
WOODY'SFeatures 6” of 60° carbide1/2” round bar with Flat-Top® designProvides safety and control for both studded and un-studded sledsSome skis may requir...
View full detailsWOODY'S HARDWELD WEAR BAR (COMPOSITE ONLY) (HSY-6580-1)
WOODY'SA hardweld runner designed for extreme service or utility applicationsDouble bead of hardweld increases the depth of the runner for controllability...
View full detailsWOODY'S 4" X 60 TURNING 1 1/2" END PAD (DY4-6580-1)
WOODY'SThese 60° carbides reduce darting as they carve through existing grooves from single runners and spread the pressure across two points, extending t...
View full detailsWOODY'S HARDWELD WEAR BAR (COMPOSITE ONLY) (HSD-8250-1)
WOODY'SA hardweld runner designed for extreme service or utility applicationsDouble bead of hardweld increases the depth of the runner for controllability...
View full detailsWOODY'S HARDWELD WEAR BAR (COMPOSITE ONLY) (HSA-9750-1)
WOODY'SA hardweld runner designed for extreme service or utility applicationsDouble bead of hardweld increases the depth of the runner for controllability...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (DY6-6580-1)
WOODY'SThese 60° carbides reduce darting as they carve through existing grooves from single runners and spread the pressure across two points, extending t...
View full detailsWOODY'S HARDWELD WEAR BAR (COMPOSITE ONLY) (HSA-9975-1)
WOODY'SA hardweld runner designed for extreme service or utility applicationsDouble bead of hardweld increases the depth of the runner for controllability...
View full detailsWOODY'S 4" X 60 TURNING 1 1/2" END PAD (DS4-8250-1)
WOODY'SThese 60° carbides reduce darting as they carve through existing grooves from single runners and spread the pressure across two points, extending t...
View full detailsWOODY'S 4" X 60 TURNING 1 1/2" END PAD (DA4-9975-1)
WOODY'SThese 60° carbides reduce darting as they carve through existing grooves from single runners and spread the pressure across two points, extending t...
View full detailsWOODY'S 6" X 60 TURNING 1 1/2" END PAD (DA6-9975-1)
WOODY'SThese 60° carbides reduce darting as they carve through existing grooves from single runners and spread the pressure across two points, extending t...
View full detailsWOODY'S ROUND DIGGER ALUM SUPPPRT PLATE GRB 48PC
WOODY'SFor most single and combination studding patterns
WOODY'S DOUBLE DIGGER ALUMSUPPORT PLATE (BLUE)
WOODY'SDual stud mounting with more rigidity and less weight than two aluminum plates or comparable steel platesFor use with 5/16" push-through studs
WOODY'S ROUND DIGGER ALUM SUPPORT PLATE ORN 48PC
WOODY'SFor most single and combination studding patterns
WOODY'S DOUBLE DIGGER ALUM SUPPORT PLATE (RED)
WOODY'SDual stud mounting with more rigidity and less weight than two aluminum plates or comparable steel platesFor use with 5/16" push-through studs